Easy audio mixer9/9/2023 This software has all tools to make your work stand over the rest. If you need to create presentations, podcasts, or even music. With it, you will be creating your own audio projects even if you never used a multi track editor or a mixer. Easy audio mixer is a multi track editor designed for average users. Mix music, create presentations, podcasts, or record yourself singing. Note that there is a minus sign there as the op-amp is working in its inverting mode.Have a recording studio at your disposal. This can be simplified into -A(V1+V2+v3), thus called a summing amplifier. The gain of the summing amplifier is expressed as A = R12/R14 or 10X and the output of the combined inputs is Vout = -(A*V1+A*V2+ A*V3). Potentiometer R11 sets the final output level before it is sent to the output jack. This is amplified 10 times by U1.4 because the gain of the op-amp is defined by the ratio of R12 to any one of the input resistors. The input to U1.4 is a virtual earth, which causes the virtual voltage at this point to be the sum of all three inputs. Resistors R14, R10, and R13 are the actual mixer part. Resistor R3 is only there to prevent scratchy noise as the potentiometer is adjusted.Ĭapacitor C1 provides a high-frequency roll-off filter to keep out radio frequency interference and inaudible signal oscillations.Īfter the pre-amplification step, switches S1, S2, and S3 will allow us to mute any channel. This potentiometer sets the actual level of each input as it will be presented to the summing amplifier. Potentiometer R1 sets the gain of the input amplifier. Their function is to provide a suitable input impedance to the microphones and this is set to 47k by resistors R2, R4, and R7. LM324 op-amps U1.1, U1.2, and U1.3 are the input pre-amplifiers. Note that all potentiometers should be the logarithmic type (audio taper). Resistors R15 and R16 divide the supply rail in half and provide a 6V bias voltage for all the non-inverting inputs. Switches S1, S2, and S3 turn the channels off. The purpose of this is to keep a constant DC bias on the op-amp and prevent slider noise.Ĭapacitors C1, C3, and C5 tailor the upper-frequency response to 20kHz, while the input capacitors C2, C4, and C6 tailor the lower frequency response to 20Hz. All four op-amps used in the circuit above are from a single LM324 chip.ġM Ohm resistors R3, R6, and R9 are in parallel with the input potentiometers. The LM324 is designed for single-supply operation and has four separate op-amps. I used a common LM324 quad op-amp (not the best for low noise and some low noise quad op-amps might be quieter, but I had some lying around). The mixer will run on a single supply from a 12V power supply (this imposes a severe constraint on the range of signal headroom). So here, the input impedance will be 47k to match most audio sources and dynamic microphones. We want the input impedance presented to each input to be constant and not a function of the gain setting. To make this a stereo mixer, simply duplicate the circuit for the other channel. The schematic below is for a mono three-channel mixer with a master volume. Our mixer will have two stages: one input pre-amplifier per channel and an output summing amplifier. Our Designįor this tutorial, we will build a mixer of our own design. The circuit on the right does have the advantage of dealing with extreme input levels. The circuit on the left will have a varying input impedance depending on the slider setting, and the circuit on the right will cause a change in level on the adjacent channels when the slider is right down low. But I have avoided them for a couple of reasons. Shown below are some input scenarios you may see on the internet. The basic idea behind a mixer is this: different inputs are fed into a common summing point, and these are added and then multiplied by the gain of the summing amplifier. A professional-level mixer may have dozens of channels and settings for each channel, including presets, built-in effects, graphic equalizers, monitor controls, and output amplifiers to name a few.īut for this article, we are going to build a more simple, but still effective three channel stereo audio mixer.
0 Comments
Leave a Reply.AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |